“蜡烛火焰划分”实验的局限成因分析及改进研究

人教版初中化学首个探究性实验"蜡烛及其燃烧"明确指出火焰的划分方法，但在实际教学中肉眼观察法和火柴梗燃烧法对蜡烛火焰的划分存在一定的局限性。采用文献研究法和实验验证法分析其局限性的成因——燃料的析炭能力强弱、材料结构的不同等，并提出相应的改进建议。     

化学法改性煤沥青脱除苯并芘的研究

在管式反应器中采用苯甲酸、聚乙二醇、固体古马隆树脂（S）、液体古马隆树脂（L）为添加剂来降低煤沥青中有害物质苯并芘的含量，以期使得煤沥青可绿色化应用。采用紫外-可见分光光度计分析煤沥青中苯并芘含量。考察了反应温度、反应时间、添加剂添加量、催化剂等工艺条件对添加剂脱除煤沥青中苯并芘的影响。结果表明，不同工艺条件能降低煤沥青中苯并芘的含量。在优化条件下，不同添加剂对苯并芘脱除率由高到低依次为：液体古马隆树脂、聚乙二醇、苯甲酸和固体古马隆树脂。分析其反应机理，这与催化剂的酸性相关，发生亲电取代反应。结果表明，液体古马隆树脂（L）在催化剂存在下对煤沥青中苯并芘脱除率可达73.0%，显示了良好的应用前景。     

自由基浓度测定方法的再验证及其在煤化学中应用

对前人建立的标准曲线法测煤中自由基浓度进行优化,以DPPH标准样品和基准样品的二次积分面积比值为新参数,结果显示新参数标准曲线法的实测值与理论值相对误差都在5%以内;重复性、复现性实验的相对标准偏差都小于3%。将新参数标准曲线法用于分析不同煤化程度煤和新疆黑山煤(HS)沥青质的自由基浓度,发现随着煤化程度增加,其煤中自由基浓度逐渐增大,从低阶褐煤的8.531×10~(17)/g上升到高阶无烟煤3.37899×10~(19)/g;而在HS煤液化过程中,随着加氢液化温度的升高,其沥青质自由基浓度逐渐下降,从290℃的1.5793×10~(18)/g降到450℃的7.410×10~(17)/g,沥青质自由基浓度变化趋势与其产率变化趋势相一致。     

不同变质程度煤的高分辨率透射电镜分析

利用高分辨率透射电子显微镜(HRTEM)分析了三种不同变质程度煤样的结构特征。基于傅里叶-反傅里叶变换方法,并结合Matlab、Arcgis和Auto CAD软件,通过图像分析技术,获得了HRTEM照片的晶格条纹参数。结果表明,三种煤样的晶格条纹呈现不同特征,按条纹长度分别归属于1×1-8×8共计八个类型。以3×3为临界点,在1×1和2×2中,ML-8中芳香层片的比例高于DP-4和XM-3;在3×3-8×8中,ML-8中芳香层片的比例低于DP-4和XM-3。对比HRTEM和XRD参数d002发现,随着镜质组反射率的增加d002都呈现递减趋势。     

On the Fundamental Polymer Chemistry of Inverse Vulcanization for Statistical and Segmented Copolymers from Elemental Sulfur

In this concept review, the fundamental and polymerization chemistry of inverse vulcanization for the preparation of statistical and segmented sulfur copolymers, which have been actively developed and advanced in various applications over the past decade is discussed. This concept review delves into a discussion of step-growth polymerization constructs to describe the inverse vulcanization process and discuss prepolymer approaches for the synthesis of segmented sulfur polyurethanes. Furthermore, this concept review discusses the advantages of inverse vulcanization in conjunction with dynamic covalent polymerization and post-polymerization modifications to prepare segmented block copolymers with enhanced thermomechanical and flame retardant properties of these materials.     

CH4/空气简化动力学机理数值验证

选择绕圆柱预混燃烧算例，验证CH₄/空气三种简化动力学机理（16s41r、15s19r和53s325r）.考虑均匀来流，忽略湍流和湍流与燃烧相互作用以及燃料扩散效应，假设层流有限反应速率，采用保自由流5阶WENO格式求解多组分Euler方程组，得到CH₄/空气预混燃烧流场温度等值线、沿驻点线压力和温度及其CH₄、CO和CO₂质量百分数分布.结果表明：三种简化动力学机理给出的流场均出现弓形激波和火焰面，弓形激波和火焰驻点距离及其形状、诱导区宽度和简化动力学机理相关.当圆柱直径增大，弓形激波和火焰向圆柱上游移动，对应的驻点距离均增大，诱导区宽度变短，点火延时变小，但火焰和弓形激波位置次序未变化.53s325r模型要比16s41r模型和15s19r模型精度要高，点火延时覆盖的压力和温度范围也较宽，所有简化机理均未完全反应，在较大圆柱直径下游达到化学平衡.     

Novel cardo polyamides with high solubility,thermally stability,and flame retardancy

Abstract

A new monomeric building block was prepared via three consecutive reactions. 4-(4-Nitrobenzyl)pyridine was catalytically reduced to 4-(4-aminobenzyl)pyridine by converting the nitro to amino group. In second step, the later compound was reacted with 3,5-dinitrobenzoyl chloride to obtain a dinitro compound which finally was converted to a new diamine by reduction of nitro groups. Polycondensation reactions of the diamine with diacidchlorides led to preparation of novel cardo polyamides with high thermal stability and flame retardancy, as well as improved solubility. The structure-property relations were studied by varying the diacidchlorides to investigate the effect of symmetry and aromaticity on the polymers.     

Dimensional scaling of flame propagation in discrete particulate clouds

The critical dimension necessary for a flame to propagate in suspensions of fuel particles in oxidiser is studied analytically and numerically. Two types of models are considered: First, a continuum model, wherein the individual particulate sources are not resolved and the heat release is assumed spatially uniform, is solved via conventional finite difference techniques. Second, a discrete source model, wherein the heat diffusion from individual sources is modelled via superposition of the Green's function of each source, is employed to examine the influence of the random, discrete nature of the media. Heat transfer to cold, isothermal walls and to a layer of inert gas surrounding the reactive medium are considered as the loss mechanisms. Both cylindrical and rectangular (slab) geometries of the reactive medium are considered, and the flame speed is measured as a function of the diameter and thickness of the domains, respectively. In the continuum model with inert gas confinement, a universal scaling of critical diameter to critical thickness near 2:1 is found. In the discrete source model, as the time scale of heat release of the sources is made small compared to the interparticle diffusion time, the geometric scaling between cylinders and slabs exhibits values greater than 2:1. The ability of the flame in the discrete regime to propagate in thinner slabs than predicted by continuum scaling is attributed to the flame being able to exploit local fluctuations in concentration across the slab to sustain propagation. As the heat release time of the sources is increased, the discrete source model reverts back to results consistent with the continuum model. Implications of these results for experiments are discussed.     

Effects of pressure rise rate on laminar flame speed under normal and engine-relevant conditions

Laminar flame speed (LFS) is one of the most important physicochemical properties of a combustible mixture. At normal and elevated temperatures and pressures, LFS can be measured using propagating spherical flames in a closed chamber. LFS is also used in certain turbulent premixed flame modelling for combustion in spark ignition engines. Inside the closed chamber or engine, transient pressure rise occurs during the premixed flame propagation. The effects of pressure rise rate (PRR) on LFS are examined numerically in this study. One-dimensional simulations are conducted for spherical flame propagation in a closed chamber. Detailed chemistry and transport are considered. Different values of PRR at the same temperature and pressure are achieved through changing the spherical chamber size. It is found that the effect of PRR on LFS is negligible under the normal and engine-relevant conditions considered in this study. This observation is then explained through the comparison between the unsteady and convection terms in the energy equation for a premixed flame.     

Pitch-Based Laminated Carbon Formed by Pressure Driving at Low Temperature as High-Capacity Anodes for Lithium Energy Storage Systems

Pitch has been used to prepare electrodes by high-temperature heat treatments for supercapacitors, lithium-ion batteries, on account of its rich aromatic ring structure. Here, the toluene-soluble component of pitch is used to prepare a kind of laminated carbon. This was realized by a template-free synthesis at low temperature with the addition of pressure. The toluene-soluble component has a small molecular weight, which makes the thermal deformation ability stronger and then enhances the orientation of the carbon layer with the help of pressure. The prepared anode exhibits a splendid electrochemical performance compared with the traditional graphite anode. A high stable capacity of approximately 550 mAh g⁻¹ at 50 mA g⁻¹, which is much higher than graphite (372 mAh g⁻¹), is obtained. Also, when the current density is up to 2 A g⁻¹, the capacity is about 150 mAh g⁻¹. Surprisingly, it also delivers a superior cycling performance. And when used as the anode/cathode electrode for lithium-ion capacitors, a high energy density can be obtained. The present work offers an opportunity to utilize the pitch source in lithium energy storage with promising cycle life, high energy/power density, and low cost.